Installing Interior Door
Installing interior door made easy! Beginners to professionals. The Quick Door Hanger kit is an easy to use bracket system for perfectly installing interior doors in minutes! With no shimming required, doors can literally be installed in as little as 4 minutes by the first time door installer. Best of all, this amazing door installation system is roughly the same cost as a pack of shims! How to video instructions for installing interior door. Available at most Home Depot locations, click for details!
Installing an Interior Door Video
Click Here – Door Installation Troubleshooting – Click Here
Step-by-Step instructions for Installing Interior Door
Purchase a Door to fit the Rough Opening
The framed in rough door opening for the door is usually around 2” wider than the purchased pre-hung door (not including the frame/jamb around the door). This allows for adjustment when installing the door to achieve plumb ”level”. Many new replacement doors come with packaging that holds the door square during installation, do not remove this packaging until installation is complete.
Draw a Plumb Line Down the Drywall
Measure 1/2” in from the rough opening on the hinge side of the door. Using a 6′ or 4′ level, draw a ”LEVEL” line down the drywall.
”Make sure this line is perfectly level, this line determines plumb for installing interior door”
Attach the Door Installation Brackets to the Door Jamb
To start the installing interior door, place a door installation bracket behind each of the 3 (or more) hinges, make sure to align the brackets’ clearance hole behind one of the hinges screws. This will allow the addition of a long screw through the hinges and into the wall stud for additional support. Attach the remaining 3 brackets on the other side of the jamb. Place the first bracket 8” from the top, the next bracket just above the latch stop, and the final bracket 6” from the bottom of the door.
Installing Interior Door
Place 1/2” blocks under the door if carpet is going to be used or 1/4” blocks if laminate (not needed if floor is finished). Never place the door jamb directly on an unfinished floor. Place the interior door into the opening to begin installing interior door. Using the plumb line on the wall, screw in the top bracket on the hinge side of the door. Then screw in the next 2 brackets using the same reference notch as the first. After these 3 brackets are screwed into the wall using the same reference notch for each, the door is now perfectly level. Now check the margin (gap between door and door jamb) when screwing in the final 3 brackets. Start at the top of the door and check the margin when screwing in the top bracket. Check the margin when screwing in the final 2 brackets. The door will now be perfectly hung and the blocks under the door can now be removed.
Install the Door Casing (Trim) around the Door
The door casing/trim can now be installed. Using finishing nails, nail on the door casing to complete the installation. Remove the hinge screws that the bracket’s clearance hole was placed behind and replace with a 2” screw that will go through the hinge, bracket clearance hole, and into the wall stud for additional support. (you should place a shim or wood between the door frame and the wall to prevent the screw pulling (bending) the door frame towards the wall from over tightening.
Note: The Door Casing/trim will perfectly conceal the door installation brackets. Most trim has a milled out backside that allows perfect space for the brackets. If using flat back trim, you will simply need to hammer the brackets into the drywall a little bit.
Adjustment Screw Hole
Allows for easy adjustment for perfectly installing doors!
Easy to see notches for perfectly aligning the brackets to the drawn ''Level/Plumb Line'' on the wall. Ensures a perfectly level installation!
Quick Alignment Tabs
Aligns installation bracket perfectly flush to the door jamb/frame, ensuring perfect bracket placement!
When lined up directly behind the center hinge screws, allows for the removal of small hinge frame screws to be replaced with long set screws to reinforce the installation if heavy or solid-core!
One of those “Why didn’t I think of that!” items
Saw these on Home Depots web site. Decided to watch the video and give them a try. It took me longer to put six brackets on the door then it took to hang the door! They work great and were super simple to use. I can’t wait to do the rest of the doors in my house.